定点连续形变长周期频段信息研究

研究了定点连续形变长周期频段信息和块体构造活动的关系。研究结果表明，在川滇菱形块体内，定点连续形变观测获得的长周期频段信息中的长期趋势变化除去仪器零漂等局部干扰外，基本上都和块体运动方向或者块体边界主干断裂活动方式相一致，表明在定点连续形变长周期频段信息中，也存在有与地震孕育有关的地壳形变信息。对其在预报上的作用做了初步研究。     

乌江渡水电站岩溶地区高压灌浆施工特殊情况的处理

乌江渡水电站扩机地下厂房防渗帷幕工程身处岩溶发育地区，工程地质条件复杂，地质构造以层间错动断层为主，并有部分陡倾角断层发育,岩层受构造挤压强烈，断层、节理、破碎带发育；水平岩溶、垂直岩溶发育。以此工程为例介绍了高压灌浆施工工艺，阐述了岩溶地区高压灌浆过程中出现的特殊问题并提出了处理措施。     

InSAR滑坡探测技术研究——以金沙江乌东德水电站段为例

采用3类InSAR产品和DEM数据开展金沙江流域乌东德水电站段的潜在滑坡探测，成功识别出多处已知和未知的滑坡点，并探测出滑坡体的形态及稳定性，提供了一种高效的大范围滑坡探测技术。同时采用小基线集InSAR技术对金坪子滑坡进行监测，不仅获得该滑坡的空间分区特征，也获取重点滑坡区的时间序列结果，并且与地面监测结果比较，精度达1.8 cm。展示了不同InSAR技术在不同尺度滑坡调查与监测中的应用特点。     

利用GPS拖体在万山区域测量平均海面技术研究

Wanshan area has been chosen to be the specified field to calibrate and validate(Cal/Val) the HY-2 altimeter and its follow-on satellites. In March 2018, an experiment has been conducted to determine the sea surface height(SSH) under the HY-2 A ground track(Pass No. 203). A GPS towing-body(GPS-TB) was designed to measure the SSH covering an area of about 6 km×28 km wide centered on the HY-2 A altimeter satellite ground track. Three GPS reference stations, one tide gauge and a GPS buoy were placed in the research area, in order to process and resolve the kinematic solution and check the precision of the GPS-TB respectively. All the GPS data were calculated by the GAMIT/GLOBK software and TRACK module. The sea surface was determined by the GPS-TB solution and the tide gauge placed on Zhiwan Island. Then the sea surface of this area was interpolated by Arc GIS10.2 with ordinary Kriging method. The results showed that the precision of the GPS-TB is about 1.10 cm compared with the tide gauge placed nearby, which has an equivalent precision with the GPS buoy. The interpolated sea surface has a bias of –1.5–4.0 cm with standard deviation of 0.2–2.4 cm compared with the checking line. The gradient of the measured sea surface is about 1.62 cm/km along the HY-2 orbit which shows a good agreement compared with the CLS11 mean sea surface(MSS). In the Cal/Val of satellites, the sea surface between the tide gauge/GPS buoy and the footprint of altimeter can be improved by this work.     

Establishment and application of an intelligent treating method for oil spill identification

In the identifying process of an oil spill accident, manual integral and artificial visual comparison are commonly used at present to determine the oil spill sources, these methods are time-consuming and easily affected by human factors. Therefore, it is difficult to achieve the purpose of rapid identification of an oil spill accident. In this paper, an intelligent method of automatic recognition, integration and calculation of diagnostic ratio of Gas Chromatography-Mass Spectrometer (GC/MS) spectrum are established. Firstly, four hundreds of samples collected around the world were analyzed using a standard method and Retention time locking technology (RTL) was applied to reduce the change of retention time of GC/MS spectrum. Secondly, the automatic identification, integration of n-alkanes, biomarker compounds, polycyclic aromatic hydrocarbons and calculation of the diagnostic ratios were realized by MATLAB software. Finally, a database of oil fingerprints were established and applied successfully in a spill oil accident. Based on the new method and database, we could acquire the diagnostic ratios of an oil sample and find out the suspected oil within a few minutes. This method and database can improve the efficiency in spilled oil identification.     

HHT-EEMD用于IGS站高程时间序列分析

利用经验模态分解（EMD）和整体经验模态分解（EEMD）方法，将BJFS站2000~2015年高程时间序列进行分解，发现其不仅存在1 a、0.5 a、0.25 a、2个月、1个月以及长周期等周期项，还存在以往方法很难探测出来的近似2 a周期信号。与EMD分解结果对比，整体经验模态分解可以明显减弱模式混叠现象。对各分量进行Hilbert 变换（HHT），得到时间-频率-能量的Hilbert 频谱图。结果表明，年周期和2 a周期变化是高程运动的主要贡献项。利用小波变换方法对比验证EEMD的分解结果表明，与小波分析相比，EEMD重构信号与高程序列差异的RMS更小，证明了HHT-EEMD方法在数据资料分析过程中的有效性。对环境负载及GRACE负载造成的测站位移进行功率谱分析得出，环境负载确实会造成IGS站高程时间序列的1 a、0.5 a以及季节性运动，GRACE负载还验证了2 a信号的存在。     

自动照准全站仪精密三角高程测量在跨河水准测量中的应用

随着全自动智能型全站仪的发展及光学水准仪的逐步淘汰，精密三角高程测量在跨河高程传递方面应用广泛。本文详细介绍了基于全自动照准全站仪的精密三角高程测量的四边形跨河水准测量方法的原理及步骤，并对该方法中对向观测获取跨河点间高差进行了理论推导和精度分析，证明了控制在一定跨河距离内并采取相应措施消除其他误差的情况下，该方法可用于二等水准跨河测量；最后通过实例证实了该方法能满足二等跨河水准测量精度要求。     

Sensitivity of soil parameters in unsaturated zone modelling and the relation between effective,laboratory and in situ estimates

Simulation of soil moisture content requires effective soil hydraulic parameters that are valid at the modelling scale. This study investigates how these parameters can be estimated by inverse modelling using soil moisture measurements at 25 locations at three different depths (at the surface, at 30 and 60 cm depth) on an 80 by 20 m hillslope. The study presents two global sensitivity analyses to investigate the sensitivity in simulated soil moisture content of the different hydraulic parameters used in a one‐dimensional unsaturated zone model based on Richards' equation. For estimation of the effective parameters the shuffled complex evolution algorithm is applied. These estimated parameters are compared to their measured laboratory and in situ equivalents. Soil hydraulic functions were estimated in the laboratory on 100 cm³ undisturbed soil cores collected at 115 locations situated in two horizons in three profile pits along the hillslope. Furthermore, in situ field saturated hydraulic conductivity was estimated at 120 locations using single‐ring pressure infiltrometer measurements. The sensitivity analysis of 13 soil physical parameters (saturated hydraulic conductivity (K_s), saturated moisture content (θ_s), residual moisture content (θ_r), inverse of the air‐entry value (α), van Genuchten shape parameter (n), Averjanov shape parameter (N) for both horizons, and depth (d) from surface to B horizon) in a two‐layer single column model showed that the parameter N is the least sensitive parameter. K_s of both horizons, θ_s of the A horizon and d were found to be the most sensitive parameters. Distributions over all locations of the effective parameters and the distributions of the estimated soil physical parameters from the undisturbed soil samples and the single‐ring pressure infiltrometer estimates were found significantly different at a 5% level for all parameters except for α of the A horizon and K_s and θ_s of the B horizon. Different reasons are discussed to explain these large differences. Copyright © 2004 John Wiley & Sons, Ltd.     

FBX三维模型自动转换为OBJ三维模型方法研究

本文研究实现了一种FBX三维模型自动转换为OBJ三维模型的方法,包括几何信息和材质信息的自动转换,所述方法包括获取数据、几何信息处理、材质信息处理、OBJ格式输出和材质库文件输出等步骤。     

影像全站仪在文物三维数字化测量中的应用与实践

根据影像全站仪的工作原理,总结出在文物测绘中的技术路线,研究点云数据处理过程中拼接、降噪、纹理映射的方法,并通过对模型数据采集精度的分析,给出了合理的数据模型采集值,为影像全站仪快速、可靠的在文物三维数字化建模中提供有益的借鉴。